Products

MT/PC polishing fixture is used MT/APC ferrule high density polishing. provides effective solutions to three critical issues during fiber optic connectors polishing with traditional method: (1) low polishing efficiency. (2) long operation time with fixing ferrules. Without increase in labor cost and equipment cost, one piece of MT/APC could make your polishing efficiency increase several times.

- Programmable system with memory for procedures.
- Dual MT UPC & Angled PC connector polishing;
- High volume polishing, more than 24 ferrules per cycle.
- Accommodates FC/UPC, SC/UPC, ST/UPC, LC/UPC, MU/UPC, FC/APC, MTRJ, E2000connectors.
- Excellent end-face quality.

- Up to 1.25Gb/s Data Links

- Hot-Pluggable

- 1310nm DFB laser transmitter

- Duplex LC connector

- Up to 40 km on 9/125μm SMF

- Single +3.3V Power Supply

- Low power dissipation <1W typically

- Commercial operating temperature range: 0°C to 70°C

- RoHS compliant

- Compliant with SFF-8472

Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA). The transceiver consists of four sections: the LD driver, the limiting amplifier, the FP laser and the PIN photo-detector. The module data link up to 20km in 9/125um single mode fiber.

The optical output can be disabled by a TTL logic high-level input of Tx Disable. Tx Fault is provided to indicate that degradation of the laser. Loss of signal (LOS) output is provided to indicate the loss of an input optical signal of receiver or the link status with partner.

The KCO-SFP-MM-1.25-550-01 Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA).

The transceiver consists of four sections: the LD driver, the limiting amplifier, the VCSEL laser and the PIN photo-detector. The module data link up to 550m in 50/125um multimode fiber.

The optical output can be disabled by a TTL logic high-level input of Tx Disable. Tx Fault is provided to indicate that degradation of the laser. Loss of signal (LOS) output is provided to indicate the loss of an input optical signal of receiver or the link status with partner.

KCO SFP GE T 1000M 1.25G RJ45 Copper Connector 30m Optical Transceiver Module

is compatible for Cisco GLC-T / GLC-TE/SFP-GE-T, Mikrotik S-RJ01

The KCO SFP GE T is a Cisco SFP-GE-T compatible copper transceiver module that has been designed, programmed and tested to work with Cisco brand switches and routers. It delivers dependable 1GbE (1000 Mbps) connectivity over copper cable, for 1000BASE-T compliant networks, with a maximum distance of up to 100 m.

KCO SFP+ 10G ER is a standard for 10 Gigabit Ethernet over fiber optic cables, specifically designed for long-distance transmission.

It allows for data transfer up to 40 km over single-mode fiber (SMF) at a wavelength of 1550nm.

KCO SFP+ 10G ER fiber optic modules, often implemented as SFP+ transceivers, are used in various applications where extended reach is needed, such as connecting buildings on a large campus or within a metropolitan area network.

KCO-SFP+-10G-LR is a very compact 10Gb/s optical transceiver module for serial optical communication applications at 10Gb/s, inter-converting the 10Gb/s serial electrical data stream with the 10Gb/s optical signal.

Up to 11.1Gbps Data Links
Up to 300m transmission on MMF
Power dissipation < 1W
VSCEL laser and PIN receiver
Metal enclosure, for lower EMI
2-wire interface with integrated Digital Diagnostic monitoring
Hot-pluggable SFP+ footprint
Specifications compliant with SFF 8472
Compliant with SFP+ MSA with LC connector
Single 3.3V power supply
Case operating temperature range:0°C to 70°C